Replace Lock in UPVC Door
A professional locksmith is required for your upvc door locks if they are not working properly. They are fast, efficient and can complete the task to a high standard.
It's not difficult to alter a upvc bar lock. It's just a matter of knowing what is involved and follow the steps below.
Eliminating the Barrel Lock
Upvc windows and doors are common in many types of homes. They are great for allowing sunlight into your home and are simple to open with the right key. Switching the barrel of a lock on an uPVC door is an easy job that only takes five minutes. It is a quick fix if you have lost your key, a tenant has moved out and has not returned it, or the barrel of your lock is damaged.
You'll need to take out the screws that hold the handles first. This is to remove the handles away from the way to access the lock barrel screw. Be careful not to loosen the screws too fast as this could cause damage to the handles or cause them to fall off while you're working.
After the screws are removed, look for the screw that holds the barrel lock in place on the inside of your door. This screw stands out and is a different color to the other screws on the door. Remove this screw using a Phillips screwdriver. Use replace window locks upvc use to unlock the lock and then insert it into the barrel. Turn it to the left as much as you can. This should free the barrel and make it easier to pull it out of the door.
After you've loosen the screw it's time to break the pins holding the euro cylinder in place. You'll require pliers that are strong, or mole grips to do this. Grab the protruding end of the euro cylinder and bend it from side to side, and then up and down. This will break the two support pins that are holding it in place.
When the old cylinder is out, you are able to start the process of installing the new one. To ensure you order the correct replacement, you must first determine the cylinder's size. This can be done by measuring the distance between the center of the circular keyhole and the middle of the square spindle. The measurement should be taken at the top of the spindle.
Change the Cylinder
The primary locking mechanism is an euro cylinder. These are easy to change and don't require a locksmith or handyman service. If your lock doesn't have this security, you need to replace it with one that has. They're inexpensive and could help you save money and time in the event that your locks have been compromised.
To start to begin, open the door and stand in front of it, so that you can easily reach the handle retaining screw by hand or using a suitable tool. Let it loosen a bit perhaps a quarter turn to start the process.
After this is completed the cylinder will come out easily as it is no longer held in by the screw. The next step is to determine what size replacement cylinder you require. There are around 25 different sizes to choose from. It is recommended to take the old cylinder along when you buy the new one so you can be certain it will fit.
If you're not sure of the dimensions, measure from the center of the screw hole to the end of the cylinder. You can only be sure that you're purchasing the right sized cylinders to fit your door made of upvc by measuring from the center of the screw hole to the end of the cylinder.
When you have your new cylinder in place, you can insert it into your door in reverse to the way you removed the old one. Aligning the lock cam could be difficult, but it is generally an issue of alignment.
You will now need to screw the long securing screw back into position. After this is done, you can test the new cylinder and ensure that it is secure inside the door. You can now reattach the handle to the door and then test it again. If everything is functioning properly the cylinder lock on your upvc doors has been replaced and you've added an extra layer of security to your home.
Changing the Handle
There are a variety of reasons the handle of a door or knob for the door can become loose. This could be due to wear and tear of the handle or it could be due to the square spindle in the handle becoming worn or damaged by excessive force or use. In this instance the door handle has to be replaced.
It is essential that the door be open to allow it to close between removing the handle and replacing it. Remove the screws from the inner surface of the plate by using a screwdriver. This will free your handle from the plate. Be careful not to lose these screws as they will require re-screwing into place later.
You can now remove the handles to access the cylinder lock within the door. The cylinder lock is round or bulb-shaped and is only used for multi-point locks on upvc as well as some aluminum doors. The procedure for changing the cylinder is similar to that of changing the handle, however, you'll have to remove the old cylinder from the door and replace with a brand new one.
When choosing the replacement handle, it is crucial to take into consideration its size. Make sure the handle you choose is of a similar size to the original one as it will have to be able to fit over the screws that keep the handle in place. It is best to start by looking at the size table which provides the most popular sizes of replacement handle plates and their keyhole centers.
It is also worth considering upgrading your handles on your doors made of upvc to more secure standards, like a Sold Secure SS301 or a 2* Kitemark set of security handles. This will improve the security of your home and make it easier to operate your door. These sets are slightly more expensive but the added security and peace mind is worth the cost. Having to constantly push the handle of the door up and down to shut or open it is not something you want to be doing.
Change the Lock
The lock on your uPVC door could be a weak point for thieves. Upgrade your uPVC to multipoint locking to ensure it's secure. This would include an open hook as well as deadbolts to deter burglars. A professional locksmith can help you with this, but it is also possible to do the work yourself. The process is simple and easy. You'll only require a few simple tools.
The first step is to loosen the screws that hold the handle in the position. With a screwdriver, you can take the screws off and put them in a safe spot. Then, you can lift the handle and expose the screw that holds the cylinder. You can remove this screw and replace it with a a new one. Make sure the screw is identical to the original. It must be aligned correctly with the barrel of the lock.
Changing the lock on your uPVC door could seem intimidating. You rely on it to safeguard your home, and making an error could leave you without a way to unlock the door. However, if you know how to accomplish it, the procedure is fairly simple and costs much less than hiring a locksmith.
You'll need to remove the faceplate on the inside of the lock in order to change the lock. You'll need to locate the screws inside the door, and the retaining bolt outside the door. Once you have these screws in your hands, you are able to remove and replace the faceplate.
It is possible to replace the lock of your uPVC door for several reasons. It could be due to a lost key, or a tenant moved out and did not return keys, or you simply need to improve the security of your home.
Anyone with a basic DIY skill can alter the locking mechanism made of uPVC. If the lock is stuck, you will need to check the hinges inside the mechanism. If the hinges have been lubricated and are in good condition, it can be a straightforward repair. If you aren't sure, it is best to contact a professional.